How To Clean Rusted Weight Plates

When it comes to working out, there’s nothing more frustrating than dealing with a weight plate that won’t budge. And if the rust on your weight plates is to blame, it’s likely that the frustration will only increase.

Fortunately, there are a few ways to clean off that rust and get your weight plates moving like new again. Here are three of the best methods:

Method 1: Vinegar and Salt

This is a method that’s been used for years to clean all sorts of things, and it works great on rust as well. All you need is a bowl, some white vinegar, and some table salt.

Start by pouring the vinegar into the bowl, then add enough salt until it’s all dissolved. Place the rusted weight plates in the bowl, making sure they’re fully submerged. Let them sit for at least 12 hours, then remove and wipe off the rust.

Method 2: Baking Soda

Baking soda is another household item that can be used to clean rust off of weight plates. All you need is a bowl, some baking soda, and some water.

Start by pouring the baking soda into the bowl, then add enough water until it’s all dissolved. Place the rusted weight plates in the bowl, making sure they’re fully submerged. Let them sit for at least 12 hours, then remove and wipe off the rust.

Method 3: WD-40

WD-40 is a household item that’s been used to clean rust off of a variety of objects for years. And it works great on weight plates as well. All you need is a can of WD-40 and a rag.

Start by spraying the WD-40 onto the rag, then wipe it onto the rust on the weight plates. Let it sit for a few minutes, then wipe it off. Repeat as necessary.

Whichever method you choose, make sure to rinse the weight plates thoroughly after cleaning to remove any leftover vinegar or baking soda. Then dry them off and put them back in your weight set.

And there you have it! Three methods for cleaning rust off of weight plates. Try one of them and get your weight plates moving like new again.

Gather the Necessary Cleaning Supplies

If you’re like most people, you probably have at least a few rusty weight plates lying around your home or garage. Rusty weight plates can be a pain to clean, but with the right supplies and a little bit of elbow grease, you can have them looking like new in no time.

To clean rusty weight plates, you’ll need the following supplies:

-Baking soda
-Vinegar
-Water
-Paper towel
-Rubber gloves
-Safety goggles

Start by mixing a solution of baking soda and water. The ratio should be about 3 parts baking soda to 1 part water. Soak a paper towel in the solution, and use it to scrub the rust off of the weight plates. Be sure to wear rubber gloves and safety goggles while doing this, as the baking soda can cause skin irritation and the vinegar can cause eye irritation.

If the rust doesn’t come off with the baking soda and water solution, try using a solution of vinegar and water. Again, the ratio should be about 3 parts vinegar to 1 part water. Soak a paper towel in the solution, and use it to scrub the rust off of the weight plates.

Once the rust is gone, rinse the weight plates with water and dry them with a paper towel. They should now be looking like new!

Inspect the Rusted Weight Plates

Rusted weight plates can be a pain to clean, but with a little effort, they can be restored to their former glory. First, inspect the rusted weight plates to see if any of the metal has chipped off. If so, the weight plates will need to be repaired or replaced.

Once the inspection is complete, gather the following supplies:

– WD-40
– Paper towels
– 0000 steel wool
– Safety goggles
– Rubber gloves

Spray the WD-40 onto the rusted weight plates and let them sit for a few minutes. Then, use the paper towels to scrub the plates clean. If the WD-40 doesn’t remove all of the rust, use the 0000 steel wool to scrub it off. Be sure to wear the safety goggles and rubber gloves during this step, as the steel wool can produce sparks.

Prepare a Cleaning Solution

Rusted weight plates can be a hassle to clean, but with the right preparation, it can be a relatively easy process.

To start, gather the supplies you will need:

-Bucket
-Hot water
-Dish soap
-Scrub brush
-Sponge
-Rag
-Vinegar
-Olive oil

Next, fill the bucket with hot water and add a squirt of dish soap. Add the weight plates and allow them to soak for a few minutes.

Then, use the scrub brush to scrub the plates clean. If the rust is stubborn, you can add a little vinegar to the water.

Finally, rinse the plates clean and dry them off with a rag.

To protect the plates from future rusting, you can apply a coat of olive oil.

Apply the Cleaning Solution to the Rusted Areas

Rusted weight plates can be a hassle to clean, but with the right solution and some elbow grease, they can be restored to their former glory.

The first step is to apply the cleaning solution to the rusted areas. In a small bowl, mix together 1 tablespoon of white vinegar, 1 tablespoon of baking soda, and 1 cup of water. Dip a cloth in the solution and apply it to the rusted areas of the weight plates. Allow the solution to sit on the plates for 10 minutes.

Then, use a scrub brush to scrub the plates clean. Be sure to scrub the entire surface of the plate, including the rusted areas. Rinse the plates with water and allow them to air dry.

If the rust is severe, you may need to repeat the process a few times. But with a little bit of effort, you should be able to get your weight plates looking like new again!

Scrub and Remove the Rust from the Weight Plates

Rusted weight plates can be a real pain to deal with, but with a little bit of effort, you can get them looking like new again.

The first step is to scrub off all of the rust using a stiff brush. Be sure to get into all of the nooks and crannies to remove as much of the rust as possible.

If there is any remaining rust, you can remove it with a rust remover. Apply the rust remover to a cloth and rub it onto the rust spots. Let the remover sit for a few minutes, then rinse it off with water.

Finally, dry the weight plates off with a towel and they will be good as new!

Rinse and Dry the Weight Plates Thoroughly

Rusted weight plates can be a real eyesore in the gym, and they can also be dangerous if they come loose and fall on someone. Fortunately, it’s not too difficult to clean them and get them looking new again.

The first step is to rinse the weight plates thoroughly. You can use a hose or a bucket of water, whichever is more convenient. Make sure to get all of the rust and dirt off of them.

The next step is to dry the weight plates. This can be done with a towel or a blow dryer. Make sure they are completely dry before putting them back on the rack.

If there is still some rust on the weight plates, you can use a rust remover to get it off. Be sure to follow the instructions on the bottle, and test the remover on a small area of the weight plate first to make sure it doesn’t damage the finish.

Once the weight plates are clean and dry, they will look like new again.

Protect and Maintain the Weight Plates to Prevent Future Rusting

Rusted weight plates can be both a safety hazard and an eyesore. Fortunately, there are several ways to clean them and protect them from rusting in the future.

The first step is to remove any loose rust with a wire brush. Next, soak the plates in a vinegar or lemon juice solution for several hours. Finally, rinse them off and coat them with a rust-inhibiting spray.

It’s important to clean and protect your weight plates on a regular basis, especially if you live in a humid environment. By following these simple steps, you can keep your weight plates looking and functioning like new for years to come.

Author

  • Amelia Jones

    Born and raised in a small town in upstate NY, Amelia has always been a creative person. After moving to the city in her early twenties, she discovered a love for organizing and helping others create a home they love. Amelia currently lives in Brooklyn with her husband and young son, and blogs about her home tips and tricks.

Related Posts