How To Clean A Maytag Washer Filter

If your Maytag washer is starting to smell, it might be time to clean the filter. The good news is, it’s an easy process! Here’s how to clean a Maytag washer filter in just a few simple steps.

1. Start by unplugging your washer from the power outlet.

2. Next, locate the filter. On most Maytag washers, it’s located behind the kick panel at the bottom of the machine.

3. Once you’ve found the filter, remove it from the washer.

4. The next step is to rinse the filter under cold water. Be sure to remove any dirt or debris that might be clogging it up.

5. If the filter is extremely dirty, you can also soak it in a mixture of equal parts white vinegar and water for about 30 minutes.

6. After soaking, rinse the filter again under cold water.

7. Finally, replace the filter and reattach it to the washer.

And that’s it! Just remember to clean your Maytag washer filter every few months to keep it running smoothly.

Importance of Cleaning the Maytag Washer Filter

If you have a Maytag washer, it’s important to keep the filter clean. The filter helps to prevent lint and other debris from clogging the washer’s pump and draining system. A clogged filter can cause the washer to overheat and shut down, or even cause a fire.

To clean the filter, first remove it from the washer. Most filters can be removed by simply pulling on them. If your filter is difficult to remove, consult your owner’s manual for instructions.

Once the filter is removed, rinse it under warm water to remove any lint or debris. If the filter is very dirty, you may need to soak it in a mixture of warm water and vinegar for a few minutes.

Once the filter is clean, replace it in the washer and run a short cycle with hot water to rinse any remaining debris.

Tools Needed for Cleaning

If your Maytag washer is leaving behind lint or fabric softener residue, it might be time to clean the washer filter. Here’s how:

You’ll need:

-A small screwdriver
-A pair of pliers
-A toothbrush
-A bowl
-Mild dish soap
-Warm water

First, locate the filter. It’s usually located near the bottom of the washer tub, on the back or underside of the washer.

With a small screwdriver, remove the screws that hold the filter in place. Be careful not to drop the screws down the drain!

With a pair of pliers, remove the filter itself. It might be dirty, so be prepared for a mess.

Place the filter in the bowl and add a squirt of mild dish soap. Use the toothbrush to scrub the filter clean.

Rinse the filter thoroughly with warm water.

Replace the filter and screw it back into place.

Run a cycle on your washer with hot water and 1 cup of vinegar to remove any soap residue.

Your Maytag washer should now be lint- and residue-free!

Locating the Maytag Washer Filter

If your Maytag washer is not draining properly, it may be due to a clogged drain filter. The drain filter is located under the washer’s main wash tub, near the drain hose. To clean the drain filter, first unplug the washer from the power outlet and then open the washer’s lid. Next, locate the drain filter cover and remove it. The cover is usually marked with an arrow or the word “Filter.”

Once the cover is removed, you will see the drain filter. The filter may be located in a mesh bag or it may be a screen that is attached to the washer’s tub. If the filter is in a mesh bag, simply remove the bag and empty it into the trash. If the filter is a screen, carefully remove it from the washer and rinse it off with warm water. Be sure to clean any debris or lint from the screen before replacing it.

Once the drain filter is clean, replace the cover and plug the washer back in. Run a test cycle to be sure that the washer is draining properly.

Removing the Filter

If your Maytag washing machine is not draining properly, it may be due to a clogged filter. In this case, you will need to clean the filter to get your machine running properly again. Here is a step-by-step guide on how to clean a Maytag washer filter.

1. Unplug your washing machine from the power outlet.

2. Remove the screws that hold the washing machine’s access panel in place. The location of the screws will vary depending on your model of washing machine.

3. Once the access panel is removed, you will be able to see the filter.

4. Use a pair of pliers to remove the filter from its housing.

5. Rinse the filter off with water. If the filter is very dirty, you may need to scrub it with a brush to remove all the dirt and grime.

6. Put the filter back in its housing and screw the access panel back on.

7. Plug your washing machine back in and turn it on. Your machine should now be draining properly.

Cleaning the Filter

If your Maytag washer is leaving behind lint or fabric debris, it’s time to clean the washer filter. Located near the water pump on the front of your washer, the filter is easy to remove and clean. Use these steps to clean your Maytag washer filter.

What You’ll Need:

-Gloves
-Rags or towels
-Bucket
-Warm, soapy water

Step 1: Put on gloves to protect your hands from the sharp edges on the filter housing.

Step 2: Locate the filter housing on the front of your washer. The housing is usually white and has a handle that you can grip to remove the filter.

Step 3: Pull the filter housing straight out from the washer.

Step 4: Inspect the filter for lint, hair, or other debris. If the filter is clean, skip to Step 7.

Step 5: If the filter is dirty, rinse it off with warm, soapy water. Use a rag or towel to scrub away any stubborn debris.

Step 6: Rinse the filter with clean water.

Step 7: Replace the filter by aligning it with the housing and pushing it back into place.

Step 8: Close the housing lid.

Your Maytag washer filter is now clean and you can resume doing laundry!

Reinstalling the Filter

If your Maytag washer is not draining properly, one possible issue is a clogged filter. In this blog post, we’ll show you how to clean your Maytag washer filter and reinstall it properly.

The first step is to locate the filter. On most Maytag washers, the filter is located on the back of the washer near the bottom. Once you’ve located the filter, remove it by unscrewing it from the washer.

Once the filter is removed, rinse it off with water. You may also need to use a brush to remove any stubborn dirt or debris. Once the filter is clean, screw it back into place.

If your washer is still not draining properly after cleaning the filter, there may be another issue causing the problem. We recommend calling a Maytag service technician to diagnose and repair the issue.

Regular Maintenance Tips for a Clean Washer Filter

If your Maytag washer is not draining properly, one of the first things you should check is the washer filter. A clogged filter can cause all sorts of problems, including poor draining, leaks, and even mold growth. Fortunately, cleaning your washer filter is a simple process that only takes a few minutes. Here’s how to do it:

1. Start by unplugging your washer from the power outlet.

2. Next, locate the filter. On most Maytag washers, the filter is located behind the kickplate, near the bottom of the machine.

3. Once you’ve located the filter, remove it by unscrewing the retaining ring that holds it in place.

4. With the filter removed, take a look inside the filter housing. If you see any dirt or debris, use a soft brush or a vacuum cleaner to remove it.

5. Once the housing is clean, reattach the filter and screw the retaining ring back in place.

6. Finally, plug your washer back in and resume using it as normal.

Cleaning your washer filter on a regular basis is a good way to keep your machine running smoothly. Try to clean the filter at least once every three months, or more often if you notice that your washer isn’t draining properly.

Author

  • Amelia Jones

    Born and raised in a small town in upstate NY, Amelia has always been a creative person. After moving to the city in her early twenties, she discovered a love for organizing and helping others create a home they love. Amelia currently lives in Brooklyn with her husband and young son, and blogs about her home tips and tricks.

Related Posts